Mua pca9685

Mô tả sản phẩm: IC MCU 32BIT 256KB FLASH 64LQFP ARM® Cortex®-M3 STM32F1 Microcontroller IC 32-Bit 72MHz 256KB (256K x 8) FLASH 64-LQFP (10x10). Vi điều khiển IC chất lượng cao -->> Linhkiendientuso.vn luôn có GIÁ ƯU ĐÃI cho những đơn hàng có số lượng lớn và HỖ TRỢ các đơn hàng nhỏ! -->>Liên hệ hotline: 0243 999 1313; Zalo:0386107520 hoặc Facebook: https://www.facebook.com/tuannguyen.tran.58367116 để được hỗ trợ tốt nhất. Ship COD thu tiền tiền trên toàn quốc. Địa chỉ: Khu đô thị Việt Hưng- Long Biên- Hà Nội （hàng ko có sẵn phải đợi từ 7-10

Mạch Điều Khiển Servo/PWM 16 Kênh I2C PCA9685 MÔ TẢ Mạch điều khiển 16 Chanel PWM PCA9685 được sử dụng để có thể xuất ra đồng thời 16 xung PWM từ 16 cổng khác nhau thông qua giao tiếp I2C sử dụng IC PCA9685, giúp bạn có thể điều khiển đồng thời 16 RC Servo hoặc Dimmer 16 thiết bị đồng thời,... Mạch điều khiển 16 Chanel PWM PCA9685 có cấu trúc phần cứng phần cứng đơn giản cũng như bộ thư viện có sẵn trên Arduino nên rất dễ dàng sử dụng và kết nối. Mạch điều khiển 16 Chanel PWM PCA9685 có chất lượng phần cứng, gia công tốt, độ bền cao, phù hợp cho các nhu cầu cần điều khiển nhiều xung PWM như Robot cánh tay máy, Robot nhện,... Thông số kỹ thuật: Mạch điều khiển 16 Chanel PWM PCA9685 IC chính: PCA9685 Điện áp sử dụng: 2.3 ~ 5.5VDC. Số kênh PWM: 16 kênh, tần số: 40~1000Hz Độ phân giải PWM: 12bit. Giao tiếp: I2C (chấp nhận mức Logic TTL 3 ~ 5VDC) Kích thước: 62.5mm x 25.4mm x 3mm ----------------------- HOTLINE: 024.2021.4848 ZALO : 0987.988.041 Địa chỉ mua hàng tại Hà Nội: 26- Ngõ 106- Lê Thanh Nghị- Hai Bà Trưng- Hà Nội ----------------------- Linh Kiện Điện Tử 3M cam kết: Bán giá luôn cạnh tranh và dịch vụ sau mua tốt nhất thị trường. Cam kết hoàn tiền 100% khi sản phẩm sai quảng cáo,hoặc lỗi do nhà sản xuất. Cam kết Sản Phẩm giốn

Hello everyone, we are Reland Tech, we are mainly engaged in electronic components, electronic tools, bakery products. Customers can contact us for more product information. If there is any dissatisfaction, you can leave us a comment. We will actively correct, of course, thank you for your sincere evalua

Description This is a PCA9685 16 channel 12-bit PWM servo motor driver I2C module for Arduino robot. You want to make a robot, When we saw this chip, we quickly realized what an excellent add-on this would be. Using only two pins, control 16 free-running PWM outputs. I2C input, control 16 PWM output, you can control the 16 way servo motor Frequency: 40-1000Hz, channel number: 16 channel, resolution: 12 bit. Specification: Frequency: 40-1000Hz. Channel number: 16 channel. Resolution: 12 bit. Voltage: DC 5-10V. Color: show as pictures. Note: There might be a bit color distortions due to different computer resolutions. There might be size errors due to different computer resolutions. Package include: 1 * PCA9685 mo

16 channel 12 bit pwm i2c interface pca9685 servo driver description for arduino Using only two pins, 16 output pwm control runs free! You can even make 62 breakouts to control up to 992 output pwm. This is a pwm i2c driver controlled by a congenital clock. That means that, unlike the tlc5940 family, you don 't have to keep sending signals that bind your microcontroller, this is totally free! This is a compliant 5v, which means you can control it from a 3.3v microcontroller and still drive safely to a 6v output (this is good for when you want to control white or blue led with 3.4 forward voltage) 6 address select pin so that you can connect up to 62 of these on a single i2c bus, a total of 992 output - that 's a lot of servos or leds Adjustable pwm frequency up to about 1.6 khz Resolution 12-bit for each output-- for servos, it means about resolution 4us at an updated rate of 60hz Configurable push-pull or open-drain output Output allows the pin to disable all output quickly Including: 4pcs 3 4 male straight header (for servo / led plug) Terminal block 2-pin (for power) Header 6-pin 0.1 '' " Specs: Dimension (no header or terminal block) 2.5 '' "x 1 ''" x 0.1 '' "(62.5 mm x 25.4 mm x 3 mm) Weight (no header or terminal block): 5.5gram Weight (with 3 4 headers & terminal block): 9gram This chip using a 7-bit i2c address between 0x60 - 0x80 can be selected by a j

__________________♤Welcome Superparis Store♤_______________ ✔Ready Stock!!Buy Now! ✔COD ✔Quality Checked ✔Best price ✈Shipping in 1 day ★Surprises for you★ ☛Free Gifts:Follow Shop ❤“Like” 5 Items: Priority Shipping ✉Sent me Screenshot and Message on your order : "Free Gift"，if not will Miss ✌(Tip:We will be based on your guests in your country to send the corresponding adapter plug) ➷Wholesale retailers are welcome to negotiate long-term business with us! __________________❀Product Information❀__________________ Feature: 16 LED drivers with programmable LED brightness, each output programmable: On/Off. Programmable group blur (dim) / flashing mixed with independent LED brightness. The 1MHz Fast Mode Plus is compatible with the I2C bus interface with 30mA high drive capability on SDA to drive high capacitive buses. The output state can be programmed to change when responding or stopping a command to achieve simultaneous update of all outputs or byte-by-byte update output (default is "stop command change"). Each LED output achieves 4096-level (12-bit) linear programmable brightness from fully off (default) to maximum brightness. Low effective output enable input pin, when the pin is high, the LED output can be programmed to 0, 1 or high impedance (power-on default is high impedance). The LED output frequency (all LEDs) is typically 40Hz to 1000Hz (when the oscillator is 25MHz, the default value of the prescaler register is 1EH and will generate a 200Hz refresh rate). Software programmable for open-drain LED output selection (default push-pull) of 16 push-pull outputs (25mA sink current and 5mA pull current at 5V), no input function. Six hardware address pins allow 62 PCA9685 devices to be connected to the same I2C bus. Maximum external input clock of 50MHz is allowed. Internal power-on reset. There is a noise filter at the SDA/SCL input. There is no glitch output when powering up. 25MHz internal crystal oscillator without external devices Specification: Operating voltage range: 2.3V-5.5V (can withstand 5.5V input) Working temperature: -40 - 85 °C ESD protection: over 2000V HBM/JESD22-A114, 200V MM/JESD22-A115 and 1000V CDM/JESD22-C101 JEDEC standard: JESD78 enters lock test when it exceeds 100mA Package: TSSOP28 and HVQFN28 Board size: 6.2*2.5*0.2cm Package List: 1 * PWM Module 6 * Pin 1 * Control Module Note: The actual product color may deviate from the photo due to light. There may be a slight deviation in the measurement of produ

servo shield 16 Channel 12-bit PWM/Servo Driver-I2C interface PCA9685 for Raspberry shield module Make your own motor party with a motor shield and a fine assortment of motors! The original L293D Motorshield kit is one of our most beloved kits, We kept the ability to drive up to 4 DC motors or 2 stepper motors, but added many improvements: Instead of a L293D darlington driver, we now have the TB6612 MOSFET driver: with 1.2A per channel and 3A peak current capability. It also has much lower voltage drops across the motor so you get more torque out of your batteries, and there are built-in flyback diodes as well. Instead of using a latch and the for Arduino's PWM pins, we have a fully-dedicated PWM driver chip onboard. This chip handles all the motor and speed controls over I2C. Only two pins (SDA & SCL) are required to drive the multiple motors, and since it's I2C you can also connect any other I2C devices or shields to the same pins. This also makes it drop-in compatible with any for Arduino. Completely stackable design: 5 address-select pins means up to 32 stackable shields: that's 64 steppers or 128 DC motors! What on earth could you do with that many steppers? I have no idea but if you come up with something send us a photo because that would be a pretty glorious project. Tested compatible with for Arduino UNO, for Leonardo, for ADK/Mega R3, Due, Diecimila & Duemilanove. Works with Mega/ADK R2 and earlier with 2 wire jum

Specifications: The PCA9685 chip is wrapped in the center of the small board. It has power input terminal, green power indicator. It is convenient for you to insert 16 servo motors in 4 groups of 3-pin connectors at a time (the plug of the servo motor is slightly wider than 0.1", so you can put 4 pairs of 0.1" connectors). Reverse polarity protection of input on terminal block. Put a large capacitor on the V+ line (you will need it in some cases). The maximum external input voltage depends on this 10V1000uf capacitor. A 220ohm series resistor is placed on all PWM output lines to protect them and can easily drive the LED. Type: PCA9685 Drive Module Voltage: DC5-10V Power Supply Communication Interface: IIC Material: PCB Features: Durable, Useful, Easy to Install Size: 2.5cm x 6.1cm/0.98" x 2.4" (Approx.) Notes: Due to the light and screen setting difference, the color of item may be slightly different from the pictures. Please allow slight dimension difference due to different manual measurement. Package Includes: 1 x PCA9685 Drive Mo

Features: You want to make a robot, When we saw this chip, we quickly realized what an excellent add-on this would be. Using only two pins, control 16 free-running PWM outputs! I2C input, control 16 PWM output, you can control the 16 way servo motor. Specifications: Frequency: 40-1000Hz. Channel number: 16 channel. Resolution: 12 bit. Voltage: DC 5-10V Size: 60*25mm Color: blue Net Weight: 12 g Package Included: 1PCS*PCA9685 16 Channel 12-bit PWM/Servo Driver-I2C interface Module For Raspberry Pi Shield Module Servo Shield For Arduino Diy Kit #DIYMORE #PCA9685 #16CH #16 #Channel #12-bit #PWM #Servo #Driver #I2C #IIC #Interface #Shield #Board #Module #For #Raspberry #Pi #Servo #Shield #For #Ar

• It's an i2c-controlled PWM driver with a built in clock. That means that, unlike the TLC5940 family, you do not need to continuously send it signal tying up your microcontroller, its completely free running! • It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages) • 6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs - that's a lot of servos or LEDs • Adjustable frequency PWM up to about 1.6 KHz • 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate • Configurable push-pull or open-drain output • Output enable pin to quickly disable all the outputs We wrapped up this lovely chip into a breakout board with a couple nice extras • Terminal block for power input (or you can use the 0.1" breakouts on the side) • Reverse polarity protection on the terminal block input • Green power-good LED • 3 pin connectors in groups of 4 so you can plug in 16 servos at once (Servo plugs are slightly wider than 0.1" so you can only stack 4 next to each other on 0.1" header • "Chain-able" design • A spot to place a big capacitor on the V+ line (in case you need it) • 330 ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial • Solder jumpers for the 6 address select

DC 5-12V PCA9685 + TB6612 Stepper Motor Dual DC Motor Driver Control Board For Arduino Description: This is the DC Motor + Stepper FeatherWing which will let you use 2 x bi-polar stepper motors or 4 x brushed DC motorx (or 1 stepper and 2 DC motors).a Using our Feather Stacking Headers or Feather Female Headers you can connect a FeatherWing on top or bottom of your Feather board and let the board take flight. The original Motor shield Kit is one of our most beloved kits, which is why we decided to squish it all together on a Feather Wing to make something even smaller, lighter, and more portable! Instead of using a latch and the Arduino's PWM pins, we have a fully-dedicated PWM driver chip onboard. This chip handles all the motor and speed controls over I2C. Since the FeatherWing only uses the I2C (SDA & SCL pins), it works with any and all Feathers- ATmega32u4, ATSAM M0 or ESP8266-based. You can stack it with any other FeatherWing or with itself (just make sure you have each wing with a unique I2C address) Check out our range of Feather boards here. Features: 4 full H-Bridges: the TB6612 chipset provides 1.2A per bridge (3A peak) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 13.5VDC. Up to 4 bi-directional DC motors with individual 12-bit speed selection (about 0.02% resolution) Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil, interleaved or micro-stepping. Motors automatically disabled on power-up Big 3.5mm terminal block connectors to easily hook up wires (18-26AWG) and power Polarity protected 2-pin terminal block and jumper to connect external power, for separate logic/motor supplies Completely stackable design: 5 address-select jumper pads means up to 32 stackable wings: that's 64 steppers or 128 DC motors. Specifications: Product Size: approx. 50*25*8mm/1.73*0.62*0.62'' Net weight: approx. 9g Note: Please allow 1-3mm differs due to manual measurement. Due to the different display and different light, the picture may not reflect the actual color of the item. Thanks for your understanding. Package included: 1 x Motor Driver Controller Board 2 x Straight Pin 5 x Cable Jack Before purchase: 1. All the goods are in stock and we will dispatch immediately if we receive the order. 2.Please read the item description, if you have any question, do not hesitate to contact us. 3.Use the vouchers for more saving. Shipment： 1.1-2 days to ship(except for the pro-order item) After purchase: 1.If you are satisfied，please give us 5 stars praise. 2.Please contact us before you are going to give us bad review. We are helpful and will solve the problems. if you receive a defect item,please contact us at once with item picture or video DC 5-12V PCA9685 + TB6612 Stepper Motor Dual DC Motor Driver Control Board For Ar

✿✿ fashionapple ✿✿ Description: Want to make a hexapod walker? Maybe you're making a piece of art with tons of moving parts, or you need to drive a ton of LEDs with precise PWM output. Your microcontroller has a limited number of PWM outputs, and you find yourself running out! Not with the Adafruit 16-Channel 12-bit PWM/Servo Driver - I2C interface. With this pwm and servo driver breakout, you can control 16 free-running PWM outputs with just two pins! Need to run more than 16 PWM outputs? No problem. Chain together up to 62 of these beauties for up to an outstanding 992 PWM outputs. Features: Dimensions (no headers or terminal block) 2.5" x 1" x 0.1" (62.5mm x 25.4mm x 3mm) Weight (no headers or terminal block): 5.5grams Weight (with 3x4 headers & terminal block): 9grams This board/chip uses I2C 7-bit address between 0x60-0x80, selectable with jumpers Terminal block for power input (or you can use the 0.1" breakouts on the side) Reverse polarity protection on the terminal block input Green power-good LED 3 pin connectors in groups of 4 so you can plug in 16 servos at once (Servo plugs are slightly wider than 0.1" so you can only stack 4 next to each other on 0.1" header "Chain-able" design A spot to place a big capacitor on the V+ line (in case you need it) 220 ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial Solder jumpers for the 6 address select pins i2c-controlled PWM driver with a built in clock. Unlike the TLC5940 family, you do not need to continuously send it signal tying up your microcontroller, its completely free running! It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages) 6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs - that's a lot of servos or LEDs Adjustable frequency PWM up to about 1.6 KHz 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate Configurable push-pull or open-drain output Output enable pin to quickly disable all the ou

Dear friends, what electronic components do you need to contact us? Many of our stocks are not on the shelf. We can contact us constantly in the process of updating. We can help you cooperate with all electronic components and integrated circ

Sự miêu tả: Bạn muốn làm một chiếc xe tập đi hexapod? Có thể bạn đang tạo ra một tác phẩm nghệ thuật với hàng tấn bộ phận chuyển động hoặc bạn cần điều khiển hàng tấn đèn LED với công suất PWM chính xác. Bộ vi điều khiển của bạn có một số đầu ra PWM hạn chế và bạn thấy mình sắp hết! Không phải với Adafruit 16-kênh 12-bit PWM / Servo Driver - giao diện I2C. Với đột phá trình điều khiển pwm và servo này, bạn có thể điều khiển 16 đầu ra PWM đang chạy tự do chỉ với hai chân! Cần chạy hơn 16 đầu ra PWM? Không vấn đề gì. Chuỗi với nhau lên đến 62 trong số các tính năng này để có đầu ra lên tới 992 PWM vượt trội. Đặc trưng: Kích thước (không có tiêu đề hoặc khối đầu cuối) 2,5 "x 1" x 0,1 "(62,5mm x 25,4mm x 3mm) Trọng lượng (không có tiêu đề hoặc khối đầu cuối): 5.5gram Trọng lượng (với tiêu đề 3x4 & khối thiết bị đầu cuối): 9gram Bo mạch / chip này sử dụng địa chỉ I2C 7-bit giữa 0x60-0x80, có thể lựa chọn với jumper Khối đầu cuối cho đầu vào nguồn điện (hoặc bạn có thể sử dụng các lỗ 0,1 "ở bên cạnh) Bảo vệ phân cực ngược trên đầu vào khối thiết bị đầu cuối Đèn LED xanh tiết kiệm điện Đầu nối 3 chân trong nhóm 4 để bạn có thể cắm 16 Servo cùng một lúc (phích cắm Servo hơi rộng hơn 0,1 "nên bạn chỉ có thể xếp 4 đầu cạnh nhau trên tiêu đề 0,1" Thiết kế "có thể chuỗi" Một vị trí để đặt một tụ điện lớn trên đường V + (trong trường hợp bạn cần) Các điện trở dòng 220 ohm trên tất cả các đường ra để bảo vệ chúng và làm cho đèn LED lái xe trở nên tầm thường Bộ nhảy hàn cho 6 chân chọn địa chỉ Trình điều khiển PWM do i2c điều khiển với đồng hồ tích hợp. Không giống như dòng TLC5940, bạn không cần liên tục gửi tín hiệu buộc bộ vi điều khiển của bạn, nó chạy hoàn toàn miễn phí! Nó tuân thủ 5V, có nghĩa là bạn có thể điều khiển nó từ bộ vi điều khiển 3,3V và vẫn điều khiển an toàn đầu ra lên đến 6V (điều này rất phù hợp khi bạn muốn điều khiển đèn LED trắng hoặc xanh lam với điện áp chuyển tiếp 3,4+) 6 chân chọn địa chỉ để bạn có thể đấu dây tới 62 chân này trên một bus i2c, tổng cộng 992 đầu ra - đó là rất nhiều servo hoặc đèn LED Tần số điều chỉnh PWM lên đến khoảng 1,6 KHz Độ phân giải 12 bit cho mỗi đầu ra - đối với servo, có nghĩa là độ phân giải khoảng 4us ở tốc độ cập nhật 60Hz Đầu ra đẩy-kéo hoặc mở có thể cấu hình Pin cho phép đầu ra để nhanh chóng tắt tất cả các đầu ra Sự miêu tả: 100% thương hiệu mới, chất lượng cao Vật chất: Thành phần điện Màu sắc: Xem hình ảnh Đặc trưng: Bạn muốn tạo ra một con rô bốt, Khi chúng tôi nhìn thấy con chip này, chúng tôi nhanh chóng nhận ra đây sẽ là một tiện ích bổ sung tuyệt vời. Chỉ sử dụng hai chân, điều khiển 16 đầu ra PWM chạy tự do! Đầu vào I2C, điều khiển 16 đầu ra PWM, bạn có thể điều khiển động cơ servo 16 chiều. Thông số kỹ thuật: Tần số: 40-1000Hz. Số kênh: 16 kênh. Độ phân giải: 12 bit. Điện áp: DC 5-10V Kích thước: 60 * 25mm / 2,36 "* 0,98" Lưu ý: Do sự khác biệt giữa các màn hình khác nhau, hình ảnh có thể không phản ánh màu sắc thực tế của mặt hàng. Cảm ơn bạn!! Đóng gói: 1 x PCA9685 Mô-đun I2C trì

servo shield 16 Channel 12-bit PWM/Servo Driver-I2C interface PCA9685 for arduino or Raspberry shield module Descriptions: You want to make a cool robot, maybe a hexapod walker, or maybe just a piece of art with a lot of moving parts. Or maybe you want to drive a lot of LEDs with precise PWM output. Then you realize that your microcontroller has a limited number of PWM outputs! What now? Using only two pins, control 16 free-running PWM outputs! You can even chain up 62 breakouts to control up to 992 PWM outputs • It's an i2c-controlled PWM driver with a built in clock. That means that, unlike the TLC5940 family, you do not need to continuously send it signal tying up your microcontroller, its completely free running! • It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages) • 6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs - that's a lot of servos or LEDs • Adjustable frequency PWM up to about 1.6 KHz • 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate • Configurable push-pull or open-drain output • Output enable pin to quickly disable all the outputs We wrapped up this lovely chip into a breakout board with a couple nice extras • Terminal block for power input (or you can use the 0.1" breakouts on the side) • Reverse polarity protection on the terminal block input • Green power-good LED • 3 pin connectors in groups of 4 so you can plug in 16 servos at once (Servo plugs are slightly wider than 0.1" so you can only stack 4 next to each other on 0.1" header • "Chain-able" design • A spot to place a big capacitor on the V+ line (in case you need it) • 330 ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial • Solder jumpers for the 6 address select pins Package Included: 1pcs * servo shield 16 Channel 12-bit PWM/Servo Driver-I2C interface PCA9685 Before purchase: 1. All the goods are in stock and we will dispatch immediately if we receive the order. 2.Please read the item description, if you have any question, do not hesitate to contact us. Shipment： 1.1-2 days to ship(except for the pro-order item) After purchase: 1.If you are satisfied，please give us 5 stars praise. 2.Please contact us before you are going to give us bad review. We are helpful and will solve the problems. if you receive a defect item,please contact us at once with item picture or video #servo #shield #16 Channel #12-bit #PWM #Servo #Driver #I2C #interface #PCA9685 #for #arduino #or #Raspberry #shield #m

___________________* ❤❤ * ujewndju* ❤❤ * ___________________ Welcome to our store, we insist on the lowest price to sell the best quality items. ✔Ready Stock ✔Wholesale Price ✔Quality Checked ☀️☀️ Surprises for you ☀️☀️ ☞Shop Voucher: Get More Discount ☞Follow Shop: Free Gifts ✈Shipping in 1 day Tip: If you want a free gift, please send me the screenshot that you follow my shop ☀️☀️ Attention ☀️☀️ ❀We will be based on your guests in your country to send the corresponding adapter plug. ➷Wholesale retailers are welcome to negotiate long-term business with us! #ujewndju _______________❀Product Information❀______________ Features: The module is an excellent and wonderful part for making a robot. Only use two pins, control 16 free running PWM output! Input I2C, control 16 PWM output, can control 16 servo motor. You can insert 16 servo motors at a time in 4 sets of 3-pin connectors. Reverse polarity protection input on terminal block. Specification: Frequency:40~1000Hz Channel:16 Resolution:12 bit Voltage: 5V Size:60*25mm/2.36*0.98in Color:Blue  Weight: 12g/0.42oz Package List: 1*Mod

Product Overview: You want to make a cool robot, maybe a hexapod walker, or maybe just a piece of art with a lot of moving parts. Or maybe you want to drive a lot of LEDs with precise PWM output. Then you realize that your microcontroller has a limited number of PWM outputs! What now? Using only two pins, control 16 free-running PWM outputs! You can even chain up 62 breakouts to control up to 992 PWM outputs • It's an i2c-controlled PWM driver with a built in clock. That means that, unlike the TLC5940 family, you do not need to continuously send it signal tying up your microcontroller, its completely free running! • It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages) • 6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs - that's a lot of servos or LEDs • Adjustable frequency PWM up to about 1.6 KHz • 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate • Configurable push-pull or open-drain output • Output enable pin to quickly disable all the outputs We wrapped up this lovely chip into a breakout board with a couple nice extras • Terminal block for power input (or you can use the 0.1" breakouts on the side) • Reverse polarity protection on the terminal block input • Green power-good LED • 3 pin connectors in groups of 4 so you can plug in 16 servos at once (Servo plugs are slightly wider than 0.1" so you can only stack 4 next to each other on 0.1" header • "Chain-able" design • A spot to place a big capacitor on the V+ line (in case you need it) • 330 ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial • Solder jumpers for the 6 address select

Description: Want to make a hexapod walker? Maybe you're making a piece of art with tons of moving parts, or you need to drive a ton of LEDs with precise PWM output. Your microcontroller has a limited number of PWM outputs, and you find yourself running out! Not with the Adafruit 16-Channel 12-bit PWM/Servo Driver - I2C interface. With this pwm and servo driver breakout, you can control 16 free-running PWM outputs with just two pins! Need to run more than 16 PWM outputs? No problem. Chain together up to 62 of these beauties for up to an outstanding 992 PWM outputs. Features: Dimensions (no headers or terminal block) 2.5" x 1" x 0.1" (62.5mm x 25.4mm x 3mm) Weight (no headers or terminal block): 5.5grams Weight (with 3x4 headers & terminal block): 9grams This board/chip uses I2C 7-bit address between 0x60-0x80, selectable with jumpers Terminal block for power input (or you can use the 0.1" breakouts on the side) Reverse polarity protection on the terminal block input Green power-good LED 3 pin connectors in groups of 4 so you can plug in 16 servos at once (Servo plugs are slightly wider than 0.1" so you can only stack 4 next to each other on 0.1" header "Chain-able" design A spot to place a big capacitor on the V+ line (in case you need it) 220 ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial Solder jumpers for the 6 address select pins i2c-controlled PWM driver with a built in clock. Unlike the TLC5940 family, you do not need to continuously send it signal tying up your microcontroller, its completely free running! It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages) 6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs - that's a lot of servos or LEDs Adjustable frequency PWM up to about 1.6 KHz 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate Configurable push-pull or open-drain output Output enable pin to quickly disable all the ou

16 Channel 12-bit PWM/Servo Driver-I2C interface-PCA9685 or Raspberry pi shield module servo shield 16 LED drivers, each output can be programmed to: Turn off Open Programmable LED brightness Programmable fuzzy group (dim) / Flashing LED brightness independent mixed with 1MHz Fast-mode Plus is compatible with high drive capability has 30mA on SDA I2C bus interface to drive highly capacitive bus Each LED output can be achieved from the fully closed (the default) to 4096 (12) between the maximum brightness linear programmable brightness Software programmable open-drain LED output selection (the default is a push-pull) of 16 push-pull outputs (at 5V 25mA sink can absorb and provide 10mA current draw), no input function Programmable output state is in response to an order to change or stop to achieve simultaneously update all outputs or by-byte (byte-by-byte) update output (default is "Stop command to change") Effective low output enable input pin when the pin is high, the LED output can be programmed to 0,1 or tri-state (high impedance power-on default) 6 hardware address pins so that the same can be connected to 62 PCA9685 I2C devices on the bus LED output frequency (all LED) is typically 40Hz to 1000Hz (When the oscillator is 25MHz, the prescaler register default value 1EH 200Hz refresh rate will generate a) 4 software programmable I2C bus address (an LED group call (Call) address and three sub-LED call (Call) address) such that the device can be set in any combination to be addressed at the same time (e.g., a register used for " All calls (All Call) "then all PCA9634 devices on the I2C bus can be addressed at the same time, while the second register for three different addresses, then a device group 1/3 bus devices can be addressed at the same time), you can enable and disable the software I2C bus address Software reset feature (SWRST Call) allows the device via I2C bus reset 25MHz internal oscillator requires no external components The maximum allowable 50MHz external clock input Internal power-on reset In the SDA / SCL inputs with noise filter Output pin has edge generation rate control No glitches on power-up (glitch) output Hot-Access Low standby current Operating voltage range: 2.3V to 5.5V 5.5V tolerant inputs Can operate at minus 40 degrees Celsius to 85 degrees Celsius environment ESD protection exceeds 2000V HBM / JESD22-A114,200V MM / JESD22-A115 and 1000V CDM / JESD22-C101 JEDEC standard JESD78 lockout exceed 100mA test Package: TSSOP28 and HV

Sự miêu tả: Bạn muốn làm một chiếc xe tập đi hexapod? Có thể bạn đang tạo ra một tác phẩm nghệ thuật với hàng tấn bộ phận chuyển động hoặc bạn cần điều khiển hàng tấn đèn LED với công suất PWM chính xác. Bộ vi điều khiển của bạn có một số đầu ra PWM hạn chế và bạn thấy mình sắp hết! Không phải với Adafruit 16-kênh 12-bit PWM / Servo Driver - giao diện I2C. Với đột phá trình điều khiển pwm và servo này, bạn có thể điều khiển 16 đầu ra PWM đang chạy tự do chỉ với hai chân! Cần chạy hơn 16 đầu ra PWM? Không vấn đề gì. Chuỗi với nhau lên đến 62 trong số các tính năng này để có đầu ra lên tới 992 PWM vượt trội. Đặc trưng: Kích thước (không có tiêu đề hoặc khối đầu cuối) 2,5 "x 1" x 0,1 "(62,5mm x 25,4mm x 3mm) Trọng lượng (không có tiêu đề hoặc khối đầu cuối): 5.5gram Trọng lượng (với tiêu đề 3x4 & khối thiết bị đầu cuối): 9gram Bo mạch / chip này sử dụng địa chỉ I2C 7-bit giữa 0x60-0x80, có thể lựa chọn với jumper Khối đầu cuối cho đầu vào nguồn điện (hoặc bạn có thể sử dụng các lỗ 0,1 "ở bên cạnh) Bảo vệ phân cực ngược trên đầu vào khối thiết bị đầu cuối Đèn LED xanh tiết kiệm điện Đầu nối 3 chân trong nhóm 4 để bạn có thể cắm 16 Servo cùng một lúc (phích cắm Servo hơi rộng hơn 0,1 "nên bạn chỉ có thể xếp 4 đầu cạnh nhau trên tiêu đề 0,1" Thiết kế "có thể chuỗi" Một vị trí để đặt một tụ điện lớn trên đường V + (trong trường hợp bạn cần) Các điện trở dòng 220 ohm trên tất cả các đường ra để bảo vệ chúng và làm cho đèn LED lái xe trở nên tầm thường Bộ nhảy hàn cho 6 chân chọn địa chỉ Trình điều khiển PWM do i2c điều khiển với đồng hồ tích hợp. Không giống như dòng TLC5940, bạn không cần liên tục gửi tín hiệu buộc bộ vi điều khiển của bạn, nó chạy hoàn toàn miễn phí! Nó tuân thủ 5V, có nghĩa là bạn có thể điều khiển nó từ bộ vi điều khiển 3,3V và vẫn điều khiển an toàn đầu ra lên đến 6V (điều này rất phù hợp khi bạn muốn điều khiển đèn LED trắng hoặc xanh lam với điện áp chuyển tiếp 3,4+) 6 chân chọn địa chỉ để bạn có thể đấu dây tới 62 chân này trên một bus i2c, tổng cộng 992 đầu ra - đó là rất nhiều servo hoặc đèn LED Tần số điều chỉnh PWM lên đến khoảng 1,6 KHz Độ phân giải 12 bit cho mỗi đầu ra - đối với servo, có nghĩa là độ phân giải khoảng 4us ở tốc độ cập nhật 60Hz Đầu ra đẩy-kéo hoặc mở có thể cấu hình Pin cho phép đầu ra để nhanh chóng tắt tất cả các đầu ra Sự miêu tả: 100% thương hiệu mới, chất lượng cao Vật chất: Thành phần điện Màu sắc: Xem hình ảnh Đặc trưng: Bạn muốn tạo ra một con rô bốt, Khi chúng tôi nhìn thấy con chip này, chúng tôi nhanh chóng nhận ra đây sẽ là một tiện ích bổ sung tuyệt vời. Chỉ sử dụng hai chân, điều khiển 16 đầu ra PWM chạy tự do! Đầu vào I2C, điều khiển 16 đầu ra PWM, bạn có thể điều khiển động cơ servo 16 chiều. Thông số kỹ thuật: Tần số: 40-1000Hz. Số kênh: 16 kênh. Độ phân giải: 12 bit. Điện áp: DC 5-10V Kích thước: 60 * 25mm / 2,36 "* 0,98" Lưu ý: Do sự khác biệt giữa các màn hình khác nhau, hình ảnh có thể không phản ánh màu sắc thực tế của mặt hàng. Cảm ơn bạn!! Đóng gói: 1 x PCA9685 Mô-đun I2C trì

Hello everyone, our company is in Shenzhen。we specialize in selling electronic components. When we receive your order, we will process your order within 24 hours. If you order many items, we may need more time to process, it will not be more than 5 days, please be patient. Genaral it need 1-2weeks arrive your hand.if you chat with us , we donot reply you, donot worry , we are try to handle your order.so pls donot cancel o

Pca9685 16 channel 12 bit pwm servo driver for raspberry arduino Specs: No. Of channels: 16 No. Of bits: 12. Input supply voltage (v): 2.3~5.5 Operating temperature (°C): - 40 ~ + 85 Oscillator frequency: 25 mhz Length (mm): 62.4 Width: 25.7. Height (mm): 2 Weight (gm): 12. Wshipment weight: 0.115 kg Shipment dimensions: 8x4

Features: You want to make a robot, When we saw this chip, we quickly realized what an excellent add-on this would be. Using only two pins, control 16 free-running PWM outputs! I2C input, control 16 PWM output, you can control the 16 way servo motor. Specifications: Frequency: 40-1000Hz. Channel number: 16 channel. Resolution: 12 bit. Voltage: DC 5-10V Size: 60*25mm Color: blue Net Weight: 12 g Package Included: 1PCS*PCA9685 16 Channel 12-bit PWM/Servo Driver-I2C interface Module For Raspberry Pi Shield Module Servo Shield For Arduino Diy Kit #DIYMORE #PCA9685 #16CH #16 #Channel #12-bit #PWM #Servo #Driver #I2C #IIC #Interface #Shield #Board #Module #For #Raspberry #Pi #Servo #Shield #For #Ar

Mô-đun điều khiển Servo PWM 16 kênh của CJMCU-PCA9685 12 bit Fm I2C - Dải điện áp hoạt động: 2.3V đến 5.5V - Đầu vào dung sai 5,5V - Nó có thể hoạt động ở nhiệt độ âm 40 độ C đến 85 độ C - Bảo vệ ESD vượt quá 2000V HBM / JESD22-A114.200V MM / JESD22-A115 và 1000V CDM / JESD22-C101 - JESEC78 tiêu chuẩn JEDEC vào bài kiểm tra khóa vượt quá

Basically all the products on the shelves in the store are in stock. You can submit the order directly. If any product is out of stock, we will notify you as soon as possible. If you cannot find the product you need in my store, please contact me to upload it, thank

PCA9685 16-Channel 12-bit PWM Servo Motor Driver I2C Module Features: This board/chip uses I2C 7-bit address between 0x60-0x80, selectable with jumpers Terminal block for power input (or you can use the 0.1" breakouts on the side) Reverse polarity protection on the terminal block input Green power-good LED 3 pin connectors in groups of 4 so you can plug in 16 servos at once (Servo plugs are slightly wider than 0.1" so you can only stack 4 next to each other on 0.1" header "Chain-able" design A spot to place a big capacitor on the V+ line (in case you need it) 220 ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial Solder jumpers for the 6 address select pins i2c-controlled PWM driver with a built in clock. Unlike the TLC5940 family, you do not need to continuously send it signal tying up your microcontroller, its completely free running! It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages) 6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs - that's a lot of servos or LEDs Adjustable frequency PWM up to about 1.6 KHz 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate Configurable push-pull or open-drain output Output enable pin to quickly disable all the outputs Package included: 1 x PCA9685 16-Channel 12-bit PWM Servo Motor Driver I2C Module For Arduino

Description This is a PCA9685 16 channel 12-bit PWM servo motor driver I2C module for Arduino robot. You want to make a robot, When we saw this chip, we quickly realized what an excellent add-on this would be. Using only two pins, control 16 free-running PWM outputs. I2C input, control 16 PWM output, you can control the 16 way servo motor Frequency: 40-1000Hz, channel number: 16 channel, resolution: 12 bit. Specification: Frequency: 40-1000Hz. Channel number: 16 channel. Resolution: 12 bit. Voltage: DC 5-10V. Color: show as pictures. Note: There might be a bit color distortions due to different computer resolutions. There might be size errors due to different computer resolutions. Package include: 1 * PCA9685 mo

Hello.this is Jointdaisy-shop,welcome! Description: Want to make a hexapod walker? Maybe you're making a piece of art with tons of moving parts, or you need to drive a ton of LEDs with precise PWM output. Your microcontroller has a limited number of PWM outputs, and you find yourself running out! Not with the Adafruit 16-Channel 12-bit PWM/Servo Driver - I2C interface. With this pwm and servo driver breakout, you can control 16 free-running PWM outputs with just two pins! Need to run more than 16 PWM outputs? No problem. Chain together up to 62 of these beauties for up to an outstanding 992 PWM outputs. Features: Dimensions (no headers or terminal block) 2.5" x 1" x 0.1" (62.5mm x 25.4mm x 3mm) Weight (no headers or terminal block): 5.5grams Weight (with 3x4 headers & terminal block): 9grams This board/chip uses I2C 7-bit address between 0x60-0x80, selectable with jumpers Terminal block for power input (or you can use the 0.1" breakouts on the side) Reverse polarity protection on the terminal block input Green power-good LED 3 pin connectors in groups of 4 so you can plug in 16 servos at once (Servo plugs are slightly wider than 0.1" so you can only stack 4 next to each other on 0.1" header "Chain-able" design A spot to place a big capacitor on the V+ line (in case you need it) 220 ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial Solder jumpers for the 6 address select pins i2c-controlled PWM driver with a built in clock. Unlike the TLC5940 family, you do not need to continuously send it signal tying up your microcontroller, its completely free running! It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages) 6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs - that's a lot of servos or LEDs Adjustable frequency PWM up to about 1.6 KHz 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate Configurable push-pull or open-drain output Output enable pin to quickly disable all the ou

Basically all the products on the shelves in the store are in stock. You can submit the order directly. If any product is out of stock, we will notify you as soon as possible. If you cannot find the product you need in my store, please contact me to upload it, thank

Features: You want to make a robot, When we saw this chip, we quickly realized what an excellent add-on this would be. Using only two pins, control 16 free-running PWM outputs! I2C input, control 16 PWM output, you can control the 16 way servo motor. Specifications: Frequency: 40-1000Hz. Channel number: 16 channel. Resolution: 12 bit. Voltage: DC 5-10V Size: 60*25mm Color: blue Net Weight: 12 g Package Included: 1 x PCA9685 16 Channel 12-bit PWM Servo motor Driver I2C Module Arduino