Pir detector

【ter】Pyroelectric Infrared PIR Motion Human Sensor Automatic Detector Module AM312Product Features: 1. Low power consumption, small size, easy to install 2. Internal use of digital signal processing, pit interference strong 3. High sensitivity, reliability, and can be widely used in automatic sensing circuit 4. Repeatable trigger mode: that is, after the induction output is high, in the delay period, if the body in its induction range of activities, the output will remain high until the delay after the person to become Low level. (Ie, the sensing module automatically detects a delay period after each activity of the human body, and takes the last active time as the starting point for the delay time). Technical Parameters: Operating voltage: DC 2.7-12V; Static power consumption: <0.1mA; Delay time: 2 seconds; Block time: 2 seconds; Trigger mode: repeatable; Sensing range: ≤ 100 degrees cone angle, 3-5 meters; (according to the specific lens) Working temperature: -20 - + 60 ° PCB Dimensions: 10mm * 8mm Module lens: small

Working parameters: Pyroelectric human body infrared sensor module, model: SR-602 Sensing distance: up to 5 meters; recommended 0-3.5M. Output: high level, H=3.3V, L=0V Power supply DC: 3.3V-15V Quiescent current: 20uA Features and uses: This module has high sensitivity, fast response, small static power consumption, small size, easy to install, and is installed. The lens, the pin header has been soldered, and the power supply is provided without debugging. Can be used for body sensor lights, alarms, security, Access control on-demand imaging, automatic equipment for agriculture, forestry and mining. Key points: 1. The high level time of the output of this product is adjustable, 2.5 seconds to 1 hour, the output time set at the factory. It is 2.5 seconds, and you can change one chip resistor if you need to change it. Please read the resistance value corresponding to the typical delay time. Refer to the relevant form below. 2. Blocking time, 2 seconds, not adjustable. 3. The factory is defined as repeatable trigger and cannot be changed. 4. The supply voltage of this module is 3.3V to 15V, and the limit voltage is 2.8V to 18V. 5. Module output timing is: output high level for 2 seconds after power-on, then go low, enter standby status. If the delay time is changed, the time when the module outputs a high level after power-on will increase accordingly, which can be understood as The startup time after entering the normal working state after the electric power will increase. 6. After installing the photosensitive element, it does not work during the day, work at night, does not contain photosensitive components, and works all day ( There are no photodiodes on the module,please purchase separately if needed. Recommended: ordinary F3 photodiode ) It is considered that there is no photosensitive element installed. 7. This module is very sensitive, pay attention to the installation position, try to avoid the heat source radiation source (air outlet / direct sunlight) 8. The sensitivity of this module is adjustable, and you need to change a chip resistor. Please read the relevant table below for details. grid. 9. When soldering with 220V ordinary soldering iron, it is necessary to unplug the power supply before welding. It is recommended to use 24V low voltage soldering iron, such as domestic white light

[ulovebsby]Pyroelectric Infrared PIR Motion Human Sensor Automatic Detector Module AM312Product Features: 1. Low power consumption, small size, easy to install 2. Internal use of digital signal processing, pit interference strong 3. High sensitivity, reliability, and can be widely used in automatic sensing circuit 4. Repeatable trigger mode: that is, after the induction output is high, in the delay period, if the body in its induction range of activities, the output will remain high until the delay after the person to become Low level. (Ie, the sensing module automatically detects a delay period after each activity of the human body, and takes the last active time as the starting point for the delay time). Technical Parameters: Operating voltage: DC 2.7-12V; Static power consumption: <0.1mA; Delay time: 2 seconds; Block time: 2 seconds; Trigger mode: repeatable; Sensing range: ≤ 100 degrees cone angle, 3-5 meters; (according to the specific lens) Working temperature: -20 - + 60 ° PCB Dimensions: 10mm * 8mm Module lens: small

CTOY DC5V-24V 12V 5A PIR Body Infrared Motion Sensor Control Detector Photosensitive Sensor Switch for Light-emitting Diode Strip Light The motion sensor switch is photosensitive and body infrared design, detect and control light intelligently and conveniently, suitable for light-emitting diode light strip. Features: Easy to install and simple to use. Photosensitive and light control - when there is a light source in the environment, it does not automatically open. When the environment is darker, it opens the detection mode. Adjust soft and stable light, no flicker. You can conveniently let the auto light on / off. The switch can detect infrared human body. According to the actual needs, users can install the human body sensors in the appropriate medium. Applicable for light-emitting diode strip lighting, incandescent lamp, energy-saving lamps, fluorescent lamp etc. Specifications: Color: Black, White (optional) Working Voltage: DC 5V-24V Output Voltage: Equal to the input voltage Load Current: <5A Static Capy Loss: ≤50uA Delay Time: The default setting is 18 seconds (4~350 seconds adjustable) Light Sensor: Yes Photosensitivity: 3lux-6lux is set by default. Detection Range: ≤110 degree cone angle, ≤3.0001M-5M Trigger Mode: Continuous trigger DC Plug Size: 5.5 * 2.1mm / 0.22 * 0.08in Item Size: 36 * 36 * 27mm / 1.42 * 1.42 * 1.06in Item Weight: 29g / 1.02ounces Package Weight: 30.6g / 1.08ounces Package Size: 65 * 55 * 30mm / 2.56 * 2.17 * 1.18in Package List: 1 * PIR Sensor Switch 1 * Screw 1 * Double-sided Adhesive

12 LED PIR Infrared Stick-on Wardrobe Night Light USB Motion Detector 5V Features: 100% brand new and high quality. 3 sensor modes: PIR motion sensor / Light sensor / Manual control. Compatible with wall charger, PC USB port, more convenient to charge. High brightness with 12LEDs, environment friendly and low power consumption. Push the button to the ON, it is in steady on state;push it to the Off, it is in off state; and push it to the Auto, it is in both light sensor and light control state, and please allow 15-20s' time delay. Built-in 600mah lithium battery, which can last for 4 hours when fully charged at ON mode and last 2 months at auto mode. Motion and light sensor. At dark place, it will light up automatically when you get into 10ft detection range and automatically light off 20 seconds later if you get out of the range. Simple installation: an adhesive strip with magnetic fields is easily attached to and detachable from the lamp body. No screws or nuts are required. Practical and durable, suitable for wardrobe, cabinet, bathroom, etc.At the same time also can be hang on the wall and used as door lamp at night. Specifications: Material: plastic Color:white Size: 12.8x4.9x1.1cm USB cable length: 49.5cm Light source: Led Led type: SMD5730 Led quantity: 12pc Light color:hot white / white Yellow light color temp: 2700k White light color temp: 6000k Detection range: 10ft Lifespan: above 80000hours Current: 500mah Delay time: 15~20s Input voltage: DC5V Output volatge: 3.7V Lumens: 55lm Working temp: -10~50 ℃ Motion angle: ≤ 100 ° Switch type: press/auto sensor Package Included: 1 x Light set Notes: 1.Due to the difference between different monitors, the picture may not reflect the actual color of the item. We guarantee the style is the same as shown in the pictures. 2.Due to the manual measurement and different measurement methods, please allow 1-3cm deviation. Th

Specification: Controllable load：3 5m Waterproof rating：IP22 Working warm clothes：-20°C~ 40°C Application lampes：LED lighting,ceiling Package Included: 1 x Motion Sensor Switch Note: This item will be shipped out without retail box, but we'll pack it

CTOY 433MHz Wireless PIR Motion Sensor Passive Infrared Detector For Home Burglar Security Alarm System without Batteries Overview: This product is a high stable infrared detector. It adopts advanced signal analysis processing technology, providing super-high detection and anti-fault alarm. When intruder passes through detection zone, the detector will detect the movement of the intruder by itself, and emit wireless signal to alarm host. The product is suitable for housing estate, villa, factory, warehouse, office building, etc. Features: *Dependable technology: Our motion detector uses state-of-the-art passive-infrared (PIR) to detect any human movement within the detection zone. Overcome false alarm. *Multi-functional: LED ON/OFF optional, delayed adjustment, sensitivity adjustment, power saving mode/use mode optional, code skipping, under-voltage indication. *Reliable range: Communication range is up to 100m/328ft (the distance from the sensors to the receiver/alarm) and detection range of the infrared sensor is approximately 8-12m/26-39ft to keep you informed and safe. *SMT design, high RFI/EMI immunity.  *Anti-burnt cover. Dynamic temperature compensation. Specifications: Working voltage: DC 9V  Working current: ≤30mA Static current: ≤20uA     Detection distance: 12m (Wide angle) Detector angle: 110° Emission distance: ≥100m (open area) Wireless frequency: 433MHz Encoded mode: 1527 Installation Way: Wall Hanging PIR Sensor battery: 1* 6F22 PP3 9V (not included)  Item Size (Without Bracket): Approx. 11.2 * 6.2 * 4.5cm(L*W*H) Item Weight: Approx. 73g / 2.6oz Package Information: Package Size: Approach. 14 * 8 * 5.5cm / 5.5 * 3.1 * 2.2in  Package Weight: Approach. 115g / 4oz    Package List: 1 * Wireless PIR Motion Sensor 1 * Bracket for PIR Sensor 1 * Set of Mounting Screws 1 * User Manual  #wirelesspirdetector #firedetector #homesecurity #Home&amp;Living #alarmsensor #moderndesign #doorsensor #Home&amp;Garden #homeimprovement #wir

Feature: 100% brand new and high quality. Small, lightweight, easy to install and operate, plug and play. Automatic ventilation exhaust fan and other electrical automatic control and other functions. Auto switch on/off in the dark when you enter into the induction range, and it may have 45s time delay. Suitable for auto lighting corridors, corridor, bathrooms, basements, warehouses, garages,closet, advertisement light box, and other places. Specification: Material: PVC Working voltage:100-240V Load power: 40W Working temp: -20 ℃ -+40 ℃ Static current: ＜ 50μA Time delay: 45s Light control: 3Lux~6Lux Output mode: sensor output Induction angle: 110 ° cone shape Induction distance: 4-6M (Note: Please allow about 1mm error due to manual measurement, and slight color difference caused by light and scr

10 LED Night Light PIR Motion Detector Lamp For Home Cabinet Bed Features: 1. The PIR: someone to open, let the automatic delay off. 2.Do not need screws, can be directly glued, suction magnet tight. 3. The use of the principle of human infrared induction, without sound and switch control, a powerful guarantee for quiet living spaces in the building. 4. Suitable for door, attic, dark, basement, garage, cellar, cellar, cabinets, cabinets, cupboards, Specifications: 1. Working voltage: DC3V-6V 2. Power supply: AAA battery (not included) 3. Time limit: 15 seconds 4. Light color: white / warm white 5. Super sensitivity distance: about 3-5 meters 6. LED QUANTITY: 10 pieces 7. Material: aluminum shell Note: this light is not waterproof and does not install in place with rain, high humidity. Package included: 1x LED PIR sensor cabinet cupboard cabinet light (battery not incl

Features: 1.Passive infrared sensor with higher precision. 2.Customized Fresnel lens, more stable and reliable. 3.Specilized detection angle design. 4.Support alamm light signal, network indicator. 5.Support on-site alarm (LED flashing) and remote alarm (push to mobile APP via Wi-Fi connection cloud platorm). 6.Long-lfle power supply design, the bttey can work 1year after fllyl charged. 7.Support low power detection, daily inspection. Specifications: Color:As picture Quantity:1PC Size:As Picture Shows Package Include:1PC WiFi PIR Motion Note: 1.Please allow 0.1-0.3cm differences due to manual measurement, thanks. 2.Please understand because of the light irradiation or computer display difference, so I can't guarantee photos and real color is 100% the

Description: Infrared sensor adopt to digital fuzzy treatment, automatic temperature compensation, Radio frequency anti-interference,has low rate of false alarm. Integrating a variety of functions,welcome,wireless doorbell ,guard defence and so on. 2 choice of power supply :3 AAA battery(not included) and 9-15v power adapter Support human voice, 32 beautiful songs and alarm 4 level of adjustable sound volume Specification: Condition: 100% Brand New Material: Plastic Power Supply: 9-12V Battery: 3 * AAA batteries (not included) Detection Angle: 110°(horizontal), 60°(vertical) Volume: 85db±5db Bell Number: 32 Product Size: Approx. 5 * 8cm / 2.0 * 3.1inch Package Includes: 1 x Door Bell Note: 1. Please use good quality alkaline batteries, avoid using less electricity and electrolyte leakage ordinary carbon battery. 2. Non-professional workers do not repair without authorization. 3. Please avoid the product installed in the rain,with long time direct sunshine,strong magnetic,heavy cold and hot air p

Welcome to 【unewkintun.vn Store】 ,We insist on the lowest price to sell the best quality items！！！Feature: 100% brand new and high quality. Small, lightweight, easy to install and operate, plug and play. Automatic ventilation exhaust fan and other electrical automatic control and other functions. Auto switch on/off in the dark when you enter into the induction range, and it may have 45s time delay. Suitable for auto lighting corridors, corridor, bathrooms, basements, warehouses, garages,closet, advertisement light box, and other places. Specification: Material: PVC Working voltage:100-240V Load power: 40W Working temp: -20 ℃ -+40 ℃ Static current: ＜ 50μA Time delay: 45s Light control: 3Lux~6Lux Output mode: sensor output Induction angle: 110 ° cone shape Induction distance: 4-6M (Note: Please allow about 1mm error due to manual measurement, and slight color difference caused by light and scr

✿ۣ Welcome To Protectionufancy ✿ۣ Specification: Brand new Fit For 433MHz Wireless Home Alarm System Size: approx. 10 x 5.5cm Color: White Working Volt: 1x 3.6v 1/2m Alkaline battery Alarm Current: less than 15mA Standy Current: less than 8uA Detecting Angle: 90degree Detecting Distance: 6~8m Installration Height: about 2.2M Alarm Output: wireless output Transmitting Distance: approx. 120m(no obstacle) Transmint Frequency: 433MHz(can be customized) Temperature: 10℃ to 60℃ (approx 50℉ ~ 140℉) Package included: 1x Wireless Motion S

Welcome to vastcoutr.vn Store ,We insist on the lowest price to sell the best quality items！！！Feature: 100% brand new and high quality. Small, lightweight, easy to install and operate, plug and play. Automatic ventilation exhaust fan and other electrical automatic control and other functions. Auto switch on/off in the dark when you enter into the induction range, and it may have 45s time delay. Suitable for auto lighting corridors, corridor, bathrooms, basements, warehouses, garages,closet, advertisement light box, and other places. Specification: Material: PVC Working voltage:100-240V Load power: 40W Working temp: -20 ℃ -+40 ℃ Static current: ＜ 50μA Time delay: 45s Light control: 3Lux~6Lux Output mode: sensor output Induction angle: 110 ° cone shape Induction distance: 4-6M (Note: Please allow about 1mm error due to manual measurement, and slight color difference caused by light and scr

<div><p>Induction of lens size: diameter: 23mm (default) Static current: <50uA High level output: 3.3 V / low 0V Working temperature: -15-+70 degrees Trigger mode: L unrepeatable trigger /H repeated trigger (Default Repeating trigger) Package Included:1pcs New HC-SR501 Infrared PIR Motion Sensor Module Blocking time: 2.5S (the default) can be produced range 0.1 seconds, tens of seconds Working voltage range: DC 4.8-20V Induction angle: <100 degree cone angle Delay time: 0.5-200S (adjustable) can be produced range 0.1 seconds - a few minutes Size: 32mm*24mm circuit board Description: It is great for microcontrollers such as for funduino and many more including the rasberry pi! It is a HC--SR501 Sensor Module With an operating voltage of 5v to 20v Operating voltage. It has a high value of 3.3 volts and a low of 0 (it is either on or off). It's delay time can be adjusted from 5 to 200seconds as well as the sensing range from 3meter to 7meters. The entire sensor with the board is 32mm by 24mm (standard pir motion sensor). The sensor either gives off a 3.3volt high value when motion is detected and then resumes or continues to give off a 0 voltage when no motion is detected. If you use an arduino or other micro controllers you can use the 3.3 volt out to power the sensor or use the 5volt power pin (vcc) to power the sensor. Either one will work.</p><

Feature: 100% brand new and high quality. Small, lightweight, easy to install and operate, plug and play. Automatic ventilation exhaust fan and other electrical automatic control and other functions. Auto switch on/off in the dark when you enter into the induction range, and it may have 45s time delay. Suitable for auto lighting corridors, corridor, bathrooms, basements, warehouses, garages,closet, advertisement light box, and other places. Specification: Material: PVC Working voltage:100-240V Load power: 40W Working temp: -20 ℃ -+40 ℃ Static current: ＜ 50μA Time delay: 45s Light control: 3Lux~6Lux Output mode: sensor output Induction angle: 110 ° cone shape Induction distance: 4-6M (Note: Please allow about 1mm error due to manual measurement, and slight color difference caused by light and scr

Description: Item type: Detector Specification: opening hole 26mm Operating voltage: 85-265V Load power: 1-40W Standby power consumption: below 0.1W Principle of induction: infrared induction Delay closing time: 15 seconds, 45 seconds, 5 minutes (adjustable) Use: temperature - 10 ° to + 45 ° Size: 45 mmx40mmx25mm Color: elegant white Photosensitive Settings: 2lux, 25lux, 2000lux (adjustable) Induction range: 4-6 meters Angle of induction: 110 degree Package Include: 1 * Detector The colors deviation might differ due to different monitor sett

Welcome to our store desertwatersuper.vn!Wish you have a good shopping. Feature: 100% brand new and high quality. Small, lightweight, easy to install and operate, plug and play. Automatic ventilation exhaust fan and other electrical automatic control and other functions. Auto switch on/off in the dark when you enter into the induction range, and it may have 45s time delay. Suitable for auto lighting corridors, corridor, bathrooms, basements, warehouses, garages,closet, advertisement light box, and other places. Specification: Material: PVC Working voltage:100-240V Load power: 40W Working temp: -20 ℃ -+40 ℃ Static current: ＜ 50μA Time delay: 45s Light control: 3Lux~6Lux Output mode: sensor output Induction angle: 110 ° cone shape Induction distance: 4-6M (Note: Please allow about 1mm error due to manual measurement, and slight color difference caused by light and scr

Description: 100% Brand New and High Quality. 1. The installation method is the same as the ceiling light, and the opening size is 4mm. 2. The active switch in the sensing area automatically extends the power-on time.  Starts timing after someone leaves. 3. The sensitivity is adjustable. The LUX knob is adjusted to the sun sign for day and night, and the moon sign is only for night. 4. High-power relay control, available energy-saving lamps, LED lights, incandescent lamps, exhaust fans, solenoid valves, monitoring equipment and other loads. 5. Wiring method: Step 1, The live and neutral wires of the AC110-240V power supply are connected to the L and N jacks of the inductive switch; Step 2, The lamp (or other electrical appliance) is connected to the L and N jacks of the inductive switch; (note that N is the common contact of the neutral line, and L is the output live line. Must be connected to lights or other electrical appliances). Specifications: Color: white Feature: infrared Sensor: motion sensor Installation way: recessed Sensing distance: 8 meters Size(approx.): opening hole size 4mm Input voltage: AC110-240V wide voltage Induction angle: 140 degrees / 360 degrees Delay adjustable range: 5 seconds to 10 minutes, adjustable sensitivity Rated load: 1200W for resistive loads (such as incandescent lamps); 300W for inductive loads such as energy-saving lamps and LED lamps; maximum allowable 10A current Package Included: 1PC * Infrared Motion Sensor Switch Note: 1. Due to the light and screen difference, the item's color may be slightly different from the pictures. 2. Please allow 0.5-2cm differences due to manual measurement. #Switch #Motion #Sensor #Infrared #Recessed #Light #Electronic #360 #Degree #Ceiling #Automatic #Det

Welcome to the shop, the quality is excellent and the price is affordable! #seyijian.vn Description: This infrared motion sensor can be used to control LED light, bulb, exhaust fan and other electric appliance, very convenient to use and consumption saving. It allows you to adjust the detection distance, ambient light and delay time. Ceiling mounted, suitable for corridor, hallway, garage, patio, toilet and anywhere needed. Features: Made of premium plastic material, not easy to aging, sturdy and durable for a long time use. Exquisite appearance design, with high sensitivity and stable performance. It adopts infrared body motion induction technology, which can achieve intelligent control and energy saving. Widely used to control LED light, compact fluorescent lamp, incandescent light bulb, alarm, exhaust fan, etc. Detection distance, ambient light and delay time are adjustable according to your actual demand. Specifications: Material: Plastic + Electronic Component Color: White Working Voltage: AC 110-240V Rated Load Current: 10A Average Load: Max. 800W(AC110V)/ Max. 1200W(AC220V) Detection Range: 120 degree(side-view)/360 degree(top-view) Detection Distance: within 6 meters in diameter(adjustable) Detection Motion Speed: 0.6~1.5m/s Ambient Light: adjustable 3~2000 lux Time-delay: Min. 5sec~Max. 7min. Working Temperature:-20~+40℃ Working Humidity: Max.93%RH Installation Height: 2~4.5m Protection Level: IP20 Diameter: approx. 115mm Thickness: approx. 57cm Package Included: 1 x Infrared Motion Sensor(with Common Installation Accessories) Wire Connection Instruction: Brown Wire: Live Input Red Wire: Live Output Blue Wire: Common Neutral Yellow Wire: Emergency power supply, will steady-on; the yellow wire doesn't need to connect if there is no emergency power supply. Note: Please allow slight error due to manual measurement. Thanks for your understanding. Monitors are not calibrated same, item color displayed in photos may be showing slightly different from the real object. Please take the real one as stan

Feature: 100% brand new and high quality. Small, lightweight, easy to install and operate, plug and play. Automatic ventilation exhaust fan and other electrical automatic control and other functions. Auto switch on/off in the dark when you enter into the induction range, and it may have 45s time delay. Suitable for auto lighting corridors, corridor, bathrooms, basements, warehouses, garages,closet, advertisement light box, and other places. Specification: Material: PVC Working voltage:100-240V Load power: 40W Working temp: -20 ℃ -+40 ℃ Static current: ＜ 50μA Time delay: 45s Light control: 3Lux~6Lux Output mode: sensor output Induction angle: 110 ° cone shape Induction distance: 4-6M (Note: Please allow about 1mm error due to manual measurement, and slight color difference caused by light and scr

Wish you have a happy shopping time! Application: For business greetings, a large mall with various gates, or a small retail store may need sensors to transmit the rings when guests arrive. For home safety, be warned if someone is approaching your exit / porch / gallery / garage door. It can also be used to monitor the elderly or children who are living separately or in need of help. Put it on the mailbox door, the ringtone will work if there is mail in your account. No more walking every hour to see if you have a letter. It can be used in all kinds of shops, upscale clubs, hotels, offices, factories, homes, banks, shops, garages, supermarkets, boutiques, villas and other places! Features: Color light, you can adjust the brightness, select 4 modes (red light / blue light / green light and LED Flash). Remote control, 280 meters in an open place, suitable for several places. The detection range of the sensor is about 2-8 m. You can place the sensor on the porch, in the gallery, in the mailbox, and in the house. 8 chord music, 40 mm speaker, more pleasant, louder. Optional ringtones. The receiver has a bell design with 36 different ringtones, from melodies to simple basic ringing of personal preferences and 5 welcome tunes for business purposes. The independent alarm speaker, up to 113dB, effectively deters thieves. 4 volume levels adjustable, has a memory function when changing batteries, attentive. Description: Micro USB power port Power supply: Receiver: 1.5 V AA batteries x 3 (not included) PIR transmitter: 1.5 V AAA Batteryx3 (not included) Sensing angle: 100 degrees horizontally and 15 degrees vertically Induction distance: 2 ～ 8m Operating range: 280m Volume: 25dB - 113dB Lighting modes: Green / Red / Blue / Flashing light Transmission and reception frequency: 433.92MHz Working ambient temperature: -10 ° C ~ + 60 ° C Work environment humidity: <80% Storage temperature: -20 ° C ~ + 70 ° C Package contents: 1 x receiver 1 x PIR transm

Package Included: 1 * Zigbee PIR sensor 1 * User manual 1 * Install accessory kit Specifications: Zigbee: Zigbee 3.0 Battery model: 2 * AAA (not included) Service life: 2 Years Operating temperature: -10-45 ℃ Relative humidity: 0-95% (non-condensing) Detection distance: 7m Indoor (for reference only) Detection Angle: 90 ° App: Tuya Smart / Smart Life Certification: CE / RoHS Gateway: Must work with Tuya Gateway Description: Note：This Zigbee senosr and detector can not work standalone without gateway. 【Advanced Motion Sensor】PIR detects human body or animals that are moving, 90° detection angle, 7m detection distance, can achieve real-time monitoring day or night. 【Emergency Alert Push Function】When there is movement detected, the alert notifications will be pushed to your phone, be aware of what's happening at home even when you're away. 【History Records Tracking】You can track the history of sensor activities. 【Strong Performance & Ultra-long Standby Time】Long transmission distance, high sensitivity, and strong network signal. Ultra-long standby time. Powered by 1*AAA batteries(not included), can last for 2

Package Included: 1*sensor,1*manual Note: Need to be used with a gateway Specifications: Battery: CR2032 3V (assuming 20 times/day, can be used for one year, can be replaced) Working temperature: -10℃~+55℃ Working humidity: 10%-90%RH (non-condensing) Detection radius: 8m Low battery warning: support Installation height: 2.2m Material: PC Communication protocol: zigbee(Zigbee hub is required, not contain) APP: Tuya/Smart life Size: 80 * 42 * 36.5mm Description: 【PIR Motion】- Sensor: A compact sensor that detects motion for your safety and convenience. 【Wireless Notifications 】- Receive instant alerts via smart phone or laptop if motion is detected inside your home unexpectedly. 【Perfect Digsn】-Advanced technology with unique structure,fine workmanship,finely processed. 【120°viewing angle】 -8m detection distance, whether day or night can be real-time monitoring. 【Small and compact appearance】 Reasonable size design, optimized internal structure, bring you convenience, beauty and enjoyment 【Zigbee hub is required】 A ZigBee gateway is required to connect the device to the Internet (ZigBee gateway is not included in the package) Notes: 【Zigbee hub is required】 A ZigBee gateway is required to connect the device to the Internet (ZigBee gateway is not included in the pac

Welcome to 【gentlehaeey.vn Store】 ,We insist on the lowest price to sell the best quality items！！！Feature: 100% brand new and high quality. Small, lightweight, easy to install and operate, plug and play. Automatic ventilation exhaust fan and other electrical automatic control and other functions. Auto switch on/off in the dark when you enter into the induction range, and it may have 45s time delay. Suitable for auto lighting corridors, corridor, bathrooms, basements, warehouses, garages,closet, advertisement light box, and other places. Specification: Material: PVC Working voltage:100-240V Load power: 40W Working temp: -20 ℃ -+40 ℃ Static current: ＜ 50μA Time delay: 45s Light control: 3Lux~6Lux Output mode: sensor output Induction angle: 110 ° cone shape Induction distance: 4-6M (Note: Please allow about 1mm error due to manual measurement, and slight color difference caused by light and scr

#AC #220V #Security #PIR #Human #Body #Motion #Sensor #Detector #Inductor #LED #Light #Switch AC 220V Security PIR Human Body Motion Sensor Detector Inductor LED Light Switch Features: Easy to install and simple to use Practical and useful Can detect human body's infrared , and use infrared to control the load Applications: Incandescent lamp, energy-saving lamps, LED lamp, fluorescent lamp and other kinds of loads. Material: ABS Size: Approx. 16 x6.0 x 4.5cm Power: AC 110-240V Detection range: 180 degree Sensor distance: 5-10m Time range: 8 sec. - 10min Environmental illumination: 2-2000LUX (adjustable) Working temperature: -10 degree ~ +40 degree Operating Humidity: Less than 93% RH Installation: open type, (hole 16mm) installation, adjustment knob facing down. Wiring: N-Blue (zero line) L-Brown (FireWire connection) Output - Red (sensor output line) Blue and brown input power Blue and red connected load (lamps) Package includes: 1 x Outdoor IR motion Sensor Switch

Features: 1.Passive infrared sensor with higher precision. 2.Customized Fresnel lens, more stable and reliable. 3.Specilized detection angle design. 4.Support alamm light signal, network indicator. 5.Support on-site alarm (LED flashing) and remote alarm (push to mobile APP via Wi-Fi connection cloud platorm). 6.Long-lfle power supply design, the bttey can work 1year after fllyl charged. 7.Support low power detection, daily inspection. Specifications: Color:As picture Quantity:1PC Size:As Picture Shows Package Include:1PC WiFi PIR Motion Note: 1.Please allow 0.1-0.3cm differences due to manual measurement, thanks. 2.Please understand because of the light irradiation or computer display difference, so I can't guarantee photos and real color is 100% the

Features: Infrared sensor with strong sensitivity, it will not affected by light,can be sensed at day and night. Strong sensitivity, no false alarm, anti-interference. Effective real-time monitoring of human movement within the monitoring range. Human body infrared automatic sensing, widely used in stores, homes, office buildings, factories and other occasions. Low power design, unique power saving e, long standby time. Exquisite appearance design, suitable for all kinds of decorative environment. Specification: Condition: Brand New Material: ABS Color: White Operating Voltage: 12V DC Power Consumption: Standard: 15mA, Alarm: 17mA Alarm Interval: 1s Sensor: Dual Anti-RF Interference: 30V/m to 1GHZ Alarm Relay: 30V DC/0.3A Disassembly-proof Relay: 30V DC/50mA Working Temperature: -10℃ ~ 60℃ Temperature Compensation: Thermistor Power Reverse Protection: Diodes Package Contents: 1 * Infrared alarm sensorOnly the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

Motion detector: When motion is detected, push notifications will be received to your phone. Temperature and humidity detector: Display the current temperature and humidity on the application. Once the temperature or humidity exceeds the preset range, an alarm notification will be sent to your . Anti-tamper function: Push notification when an intruder disassembles the sensor. USB or operating battery: It can be easily installed anywhere near the AC power outlet. There is no need to replace the battery when using the USB cable to charge. Easy to use: It can be operated without a hub. Just connect it to your Wi-Fi network and download the "Smart Life" application (note: only 2.4G Wi-Fi network is supported) WiFi USB PIR Motion Sensor Anti-demolition function, push notification when device is removed Battery: CR123A * 2-3V USB power supply: 5V / 1A Standby current: 39.7uA Wireless frequency: 2.4GHz Wireless standard: IEEE 802.11b / g / n Wifi range: 45M Sensitive angle: 110 Celsius Colour:White Material:Shell plastic Size:68mm x 56mm x 56mm Sensitive distance: 12m Package Contents: 1 * Host 1 * data lineOnly the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

Package Included: 1*Induction head 1*nut 1*pair wiring Specifications: Product name: infrared human body sensor switch Product weight: 29G Package size: 10*4*4 Working voltage: 85-265 (V) Controllable power: 1-40W Description: Type: Motion Sensor light Switch Color: White Working Voltage: AC100-240V,50/60Hz Output power:≤40W Mode Setting: Deep Dark/light Dark/All day Sensing Distance: 4-6m Time Delay: 15Secs 45Secs 5Min Angle Coverage: 110° Extreme Temperature Using: -10 celsius-+45 celsius Standby power consumption: